| 品牌 : | 德国洛克 | 型号 : | LOCKE |
| 材质 : | 不锈钢 | 类型(通道位置) : | 先导式 |
| 连接形式 : | 螺纹 | 适用介质 : | 蒸汽 |
| 流动方向 : | 双向 | 用途 : | 截止 |
| 公称通径 : | DN1～300 | 工作温度 : | -10～+80℃ |
| 使用压力 : | 0～200Mpa |
一、进口焊接高压电磁阀产品概述：
德国《LOCKE》洛克--进口焊接高压电磁阀是指与管道的连接方式采用焊接（有对焊和承插焊）高压电磁阀。由线圈驱动阀门开关，可实现对高压介质的远程自动化控制的阀门，广泛用于对高压氮气，高压水，高压气体，高压液体，高压油品等介质的开启和关闭。
1、 Overview of imported welded high pressure solenoid valve products:
German "Locke" - imported welding high-pressure solenoid valve is a kind of high-pressure solenoid valve connected with pipeline by welding (including butt welding and socket welding). The valve switch driven by coil can realize the remote automatic control of high-pressure medium. It is widely used to open and close high-pressure nitrogen, high-pressure water, high-pressure gas, high-pressure liquid, high-pressure oil and other media.
二、进口焊接高压电磁阀技术参数：
原理结构：先导活塞式
公称通径：DN1～300mm
阀体材质：不锈钢304/316
使用控制：常闭式、常开式
温度范围：-196℃～+700℃
压力范围：0.01～300mpa
接线方式：接线座式、引线式
适用介质：水、气、油、蒸汽、燃气、腐蚀流体等
防护型式：普通型、防水、防尘、防爆、船用、防腐
电源电压: DC12~127V、DC12V、DC24V/AC127V、AC220V、AC380V
接口连接：内螺纹、法兰、焊接(外螺纹和特殊接口可定做或加转接头)
介质粘度：小于50C St(大于时需定制)
2、 Technical parameters of imported welding high pressure solenoid valve:
Principle and structure: pilot piston type
Nominal diameter: DN 1 ～ 300 mm
Valve body material: stainless steel 304 / 316
Use control: normally closed, normally open
Temperature range: - 196 ℃ ~ + 700 ℃
Pressure range: 0.01 ~ 300 MPa
Wiring mode: wiring base type, lead type
Applicable media: water, gas, oil, steam, gas, corrosive fluid, etc
Protection type: common type, waterproof, dustproof, explosion-proof, marine, anti-corrosion
Power supply voltage: DC12 ~ 127V, DC12V, DC24 V / ac127v, AC220 V, AC380 V
Interface connection: internal thread, flange, welding (external thread and special interface can be customized or with adapter)
Medium viscosity: less than 50c st
三、进口焊接高压电磁阀工作原理：
常闭型：通电开启、断电关闭
常开型：通电关闭、断电开启
3、 Working principle of imported welding high pressure solenoid valve:
Normally closed: power on and power off
Normally open: power on and power off
四、进口焊接高压电磁阀性能特点：
1、类型(通道位置)：先导型二通式
2、电磁阀采用独到设计，阀口关闭性能良好，确保无任何泄露;
3、一步定位设置,使活塞上下操作方便动作永不偏离中心
4、内部结构全部采用四氟和304不锈钢填充,加强了抗磨损能力
5、在介质无压差的情况下，阀可以进行正常工作
6、简化了线圈一体化的连接，与引线式接头连接，不受范围限制极为方便;
7、配有O型圈的顶螺帽确保防水、防潮、防爆，超长寿命
8、线圈设计符合CE161-1标准，在极限条件下仍正常工作
9、流体较高工作温度700℃，较大工作压力300MPa;
10、电磁阀配有220V 20/60Hz，24V 12V线圈可以满足不同用户需要，订购时请说明。
4、 Performance characteristics of imported welded high pressure solenoid valve:
1. Type (channel location): pilot two way
2. The solenoid valve adopts unique design with good closing performance to ensure no leakage;
3. One step positioning setting makes the piston easy to operate up and down and never deviate from the center
4. The internal structure is filled with PTFE and 304 stainless steel to enhance the wear resistance
5. Under the condition of no pressure difference in the medium, the valve can work normally
6. The connection of the coil integration is simplified, and the connection with the lead type connector is not limited by the scope, which is very convenient;
7. Top nut with O-ring ensures waterproof, moisture-proof, explosion-proof and long service life
8. The coil is designed according to ce161-1 standard and works normally under limit conditions
9. The working temperature of the fluid is 700 ℃ and the working pressure is 300mpa;
10. The solenoid valve is equipped with 220 V 20 / 60 Hz, 24 V 12 V coil, which can meet the needs of different users. Please explain when ordering.